Maintaining Cloudera Navigator Encrypt

Manually Backing Up Navigator Encrypt

It is recommended that you back up Navigator Encrypt configuration directory after installation, and again after any configuration updates.

To manually back up the Navigator Encrypt configuration directory (/etc/navencrypt):
```
zip -r --encrypt nav-encrypt-conf.zip /etc/navencrypt
```
The --encrypt option prompts you to create a password used to encrypt the zip file. This password is also required to decrypt the file. Ensure that you protect the password by storing it in a secure location.
Move the backup file (nav-encrypt-conf.zip) to a secure location.

Validating Navigator Encrypt Configuration

To validate the Navigator Encrypt deployment, run the following command:

sudo navencrypt status --integrity

This command verifies that:

The mount encryption key (MEK) exists for each mount point.
Each mount point in /etc/navencrypt/ztab has a corresponding entry in the control file (/etc/navencrypt/control).
Each mount point directory exists.
For loop devices, the file used for encrypted storage exists.

The output is similar to the following:

$ sudo navencrypt status --integrity
Checking MEKs integrity

        Mountpoint: /dev/loop0
                MEK file exist: ......................   [YES]
        Mountpoint: /dev/loop1
                MEK file exist: ......................   [YES]

Checking Ztab Mountpoints integrity

         Mountpoint: /dev/loop0
                 ztab vs control correspondence: .....   [YES]
                 Mountpoint directory exists: ........   [YES]
         Mountpoint: /dev/loop1
                 ztab vs control correspondence: .....   [YES]
                 Mountpoint directory exists: ........   [YES]

Checking Datastore backend files

         Datastore: '/root/my_storage_test'
                 Backend file exist: .................   [YES]

Restoring Mount Encryption Keys (MEKs) and Control File

Navigator Encrypt deposits its mount encryption keys (MEKs) and control file (/etc/navencrypt/control) in Cloudera Navigator Key Trustee Server. If these files are accidentally deleted, they can be restored from Key Trustee Server using the following commands:

To restore MEKs:
```
sudo navencrypt key --restore-keys
```

To restore the control file:

sudo navencrypt control --restore-control-file

Access Modes

Navigator Encrypt provides three different access modes:

Enforcing is the default mode in which Navigator Encrypt validates access from all processes against the ACL. To protect your data, enforcing mode must be enabled.
Permissive mode causes action="denied" messages to be logged in dmesg. It does not prevent access to the encrypted data. This mode is a dry-run feature to run and build ACL rules.
Admin mode, as well as permissive mode, does not prevent access to the encrypted data. It allows any process to access the information because the ACL rules are not validated against the process. Admin mode does not cause action="denied" messages to be logged in dmesg.

To view the current access mode, run the following command:

sudo /usr/sbin/navencrypt status -d

To change the access mode, use the following command:

sudo /usr/sbin/navencrypt set --mode={enforcing|permissive|admin}

You cannot change the Navigator Encrypt access mode unless the Navigator Encrypt module is running. To view the status of the Navigator Encrypt module, run navencrypt status --module.

To start the Navigator Encrypt module there must be at least one active mount-point. To verify the mount-points status, run the following command:

sudo /etc/init.d/navencrypt-mount status

For RHEL 7, use systemctl instead:

sudo systemctl status navencrypt-mount

Changing and Verifying the Master Key

You can perform two operations with the navencrypt key command: change and verify.

You can verify a key against the Navigator Encrypt module, the Navigator Key Trustee server, or both. For example:

sudo /usr/sbin/navencrypt key --verify
sudo /usr/sbin/navencrypt key --verify --only-module
sudo /usr/sbin/navencrypt key --verify --only-keytrustee

The master key can be changed in the event that another key-type authentication mechanism or a new master key is required. Valid master key types are single-passphrase, dual-passphrase, and RSA key files. To change the master key type, issue the following command and follow the interactive console:

sudo /usr/sbin/navencrypt key –-change

You can use the --trustees, --votes, and --recoverable options for the new key as described in Table 1.

Listing Categories

To list the existing categories for each mount point, run the command navencrypt-move --list-categories. For example:

$ sudo navencrypt-move --list-categories
Navigator Encrypt Categories found per Mountpoint:

  /dmcrypt-storage
     @mysql
     @keytabs

  /home/jdoe/secrets
     @moms_recipes
     @world_domination_plan

Updating ACL Fingerprints

All rules reference a process fingerprint (a SHA256 digest) that is used to authenticate the process into the file system. If the file system detects a fingerprint that is different from the one stored in the ACL, the Linux process is denied access and treated as an untrusted process.

Occasionally this process fingerprint must be updated, such as when software is upgraded. When the fingerprint must be updated, the Navigator Encrypt administrator re-authenticates the process on the ACL by executing the command navencrypt acl --update.

The following example demonstrates how to determine when a process fingerprint has been changed and must be updated:

$ sudo /usr/sbin/navencrypt acl --list
Type MASTER passphrase:
# -  Type Category    Path         Profile  Process
1 !! ALLOW @mysql *            /usr/sbin/mysqld
2 ALLOW @log * /usr/sbin/mysqld
3 !! ALLOW @apache * /usr/lib/apache2/mpm-prefork/

In the example above, the double exclamation (!!) characters indicate that a process fingerprint has changed and must be updated. Similarly, double E (EE) characters indicate a process read error. This error can be caused by a process that does not exist or that has permission issues.

note

For RHEL-compatible OSes, the prelink application may also be responsible for ACL fingerprint issues. Prelinking is intended to speed up a system by reducing the time a program needs to begin. Cloudera highly recommends disabling any automated prelink jobs, which are enabled by default in some systems. As an alternative, Cloudera recommends that you integrate a manual prelink run into your existing change control policies to ensure minimal downtime for applications accessing encrypted data.

To disable prelinking, modify the /etc/sysconfig/prelink file and change PRELINKING=yes to PRELINKING=no. Then, run the /etc/cron.daily/prelink script as root. Once finished, automatic prelinking is disabled.

For more information about how prelinking affects your system, see prelink.

Managing Mount Points

The /etc/init.d/navencrypt-mount command mounts all mount points that were registered with the navencrypt-prepare command and are listed in the /etc/navencrypt/ztab file. The possible operations are:

start
stop
status
restart

For RHEL 7, use

systemctl [start|stop|status|restart]
          navencrypt-mount

.

When executing the stop operation, the encrypted mount point is unmounted, and your data becomes inaccessible.

The following example shows how to run

navencrypt-mount
          status

with some inactive mount points:

sudo /etc/init.d/navencrypt-mount status

The following example shows how to run the

navencrypt-mount
          stop

command:

sudo /etc/init.d/navencrypt-mount stop

The following example shows how to run the

navencrypt-mount
          start

command:

sudo /etc/init.d/navencrypt-mount start

Here is an example command used to manually mount a directory:

sudo /usr/sbin/mount.navencrypt /path/to_encrypted_data/ /path/to/mountpoint

This command can be executed only if the navencrypt-prepare command was previously executed.

Navigator Encrypt Kernel Module Setup

If the kernel headers were not installed on your host, or if the wrong version of the kernel headers were installed, the Navigator Encrypt module was not built at installation time. To avoid reinstalling the system, install the correct headers and run the navencrypt-module-setup command. This attempts to build the module and install it.

This method is also an efficient way to install any new Navigator Encrypt module feature or fix without otherwise modifying your current Navigator Encrypt environment.

Navigator Encrypt Configuration Directory Structure

The file and directory structure of /etc/navencrypt is as follows:

$ tree /etc/navencrypt/
/etc/navencrypt/
├── control -> /etc/navencrypt/jSpi9SM65xUIIhrau1Nn8ZXmQhrrQ9e363EUz8HKiRs
├── jSpi9SM65xUIIhrau1Nn8ZXmQhrrQ9e363EUz8HKiRs
├── rules
├── ztab
locust
└── keytrustee
	├── clientname
	├── deposits
	│   ├── dev.loop0
	│   ├── media.31E5-79B9locustlocust[system ~]# . /etc/*release[system ~]# . /etc/*release
	│   ├── mnt.a
	│   ├── mnt.encrypted
	│   └── mnt.tomount
	├── pubring.gpg
	├── pubring.gpg~
	├── random_seed
	├── secring.gpg
	├── trustdb.gpg
	└── ztrustee.conf

The following files and folders are part of the created file structure:

control
File that saves information about the mount points and corresponding Navigator Key Trustee keys. If this file is accidentally deleted, you can restore it using the navencrypt control --restore-control-file command.
rules
File that contains the ACL rules. It is encrypted with the user-provided master key.
ztab
File that contains information about all the mount points and their encryption type.
important
Use caution when editing the /etc/navencrypt/ztab file. Entries are tab-separated (not space-separated). The ztab file must not contain empty lines.
keytrustee
Directory where Navigator Key Trustee GPG keys are stored. These are generated during navencrypt register operations.
keytrustee/deposits
Directory where the Navigator Encrypt mount encryption keys (MEKs) are saved. These are encrypted with the user-provided master key. If these are accidentally deleted, you can restore them from Key Trustee Server using the navencrypt key --restore-keys command.

Every mount point has an internal randomly-generated encryption passphrase.

Collecting Navigator Encrypt Environment Information

When troubleshooting problems with Navigator Encrypt, it is helpful to gather information about the installation and environment. Navigator Encrypt provides a command to facilitate this:

sudo navencrypt-collect

This command collects and outputs to the console the following information:

Information about the system on which Navigator Encrypt is installed
Entries from /etc/navencrypt/ztab
The contents of the keytrustee.conf file
Recent entries from the Navigator Encrypt log file
Configured software repositories
Checksums of all /usr/src/navencrypt* and /usr/sbin/navencrypt* files

You can use this information to compare Navigator Encrypt installations, and you can also provide this information to Cloudera Support for troubleshooting. The navencrypt-collect command only outputs this information on the console, and does not generate any files or upload to Cloudera.

To save the information to a file, use the redirect operator (>). For example:

sudo navencrypt-collect > navencrypt.info

Upgrading Navigator Encrypt Hosts

See "Best Practices for Upgrading Navigator Encrypt Hosts" in the Upgrading Cloudera Navigator Encrypt guide for information about upgrading operating systems (OS) and kernels on hosts that have Navigator Encrypt installed.